การ Reset ตลับ รุ่น HP C6656 - C8727 ดำ - C6657 - C8728 สี
 (กรณีเครื่องแจ้ง error ไฟแดงกระพริบ ทั้งที่เพิ่งเติมหมึกมาใหม่)

 มี 3 วิธีการ และขั้นตอนต่างๆดังนี้                                                        ภาษาอังกฤษ คลิก ที่นี่


วิธีที่ 1

1. เติมหมึก ไซเบอร์ อิ้งค์ ลงในตลับ.


 


2. To reset the HP 56 black ink cartridge or HP 57 color ink cartridge, first tape over the contact pointed to by the arrow in the diagram on the left.
3. Install the cartridge back into your HP printer with the first contact covered with tape. See below for illustration of contacts. (One of the little gold-coloured squares is called a contact.)

4. The printer will tell you that there is a problem with the ink cartridge. Click "ok". The printer will then start to print an alignment page. Let the printer print the alignment page.

5. Remove the cartridge from the printer again. Leave the first piece of tape on the contact first covered. Cover the second contact shown in the picture on the lower left for the black cartridge or the contact in the picture on the lower right for the color cartridge. The second contact on the HP c6656a black cartridge to be covered is the top square on the next to last row from the left. The second contact to cover on the HP c6657a cartridge is the top square on the last row from the left.
6. Install the cartridge into the printer again. This time with both contacts being covered with tape.

7. The printer will go through the same process as before, telling you there is a problem with the cartridge. Again, click "ok". The printer will start to print an alignment sheet. Again, let the printer finish the alignment page.

8. Remove the cartridge once more from the printer. Remove both pieces of tape used to cover the contacts.

Make sure that there isn't any residue left from the tape on the contacts. If you do see residue, gently clean the contact with rubbing alcohol.

9. Install the cartridge on final time into your HP printer. The cartridge will now be read as new and full of ink.


Green square = first contact to cover
Pink square = second contact to cover


Green square = first contact to cover
Blue square = second contact to cover


METHOD 2
1. With the computer off, remove the cartridge from the printer and cover contact #1 with tape. Start up computer and printer should automatically print a test sheet.

2. Take out cartridge and cover contact #2 with tape. Reinstall cartridge. Printer will make a little noise.

3. Take out cartridge and cover contacts #3 & #4 with tape. Reinstall cartridge. (Printer will make a lot of noise. If you check ink levels now with HP inkjet utility, you’ll be given a notice that printer is busy printing.

4. Open printer lid and wait for cartridge to return to center. Remove cartridge.



5. Remove tape from Contacts #1, #2, #3, and #4. Reinstall cartridge. (If you check ink levels now, you’ll be given a notice that printer is busy printing.)
6. Turn printer off and then on again. Check ink levels — they should now register 100% full. Printer should be ready to use.

Three Cartridge Method

On some models the above procedure won't work, and you'll have to fool the printer by keeping three cartridges on hand (these cartridges can be old, empty cartridges). This works because the printer only remembers the last TWO cartridges which were in it. The procedure is as follows:

Cart #1 (empty) is removed for refilling
Cart #2 is installed
Cart #2 is removed
Cart #3 is installed
Cart #3 is removed
Cart #1 (refilled) is installed. The printer now thinks that the filled cart is new.


แปลและเรียบเรียง โดย ทีมงาน"ไซเบอร์ อิ้งค์"....หากคัดลอกไป กรุณาให้เครดิตอ้างอิงด้วยค่ะ